[2024] Skullcandy Push Active Not Charging

Hello music lovers, do you have Skullcandy push active earbuds and they are not charging?

If yes, you are in the right place.

Believe me, I’ve been through this situation too.

Topic	Skullcandy Push Active Not Charging
Category	Troubleshooting Tips for Earbuds

Imagine, you have finished all your tasks and taken some time out to listen to music, and then you see that your earbuds are out of charge.

When you put them on charge, you find out they’re not charging at all. Just think about how you would feel then!

Of course, it would be frustrating, right?

Table of Contents

But don’t worry, in this simple guide, I will tell you why your Skullcandy push active not charging and how to solve this problem.

Whether you’re a tech expert or a regular listener, I’ll give you 100% working solutions to fix your Skullcandy push active earbuds not charging issue.

So let’s get started without further ado.

Why is Skullcandy Push Active Not Charging?

There are some common reasons why your Skullcandy Push active earbuds may not charge.

1. Dirty Charging Ports

If there is dirt, lint, or debris in the charging ports of your earbuds, it can prevent the charging cable from making a proper connection. Ensure the ports are kept clean.

2. Defective Charging Cable

At times, the cable you use to charge your earbuds may require repair or replacement.

Experiment with a different cable to check if it resolves the issue.

3. Defective Battery

Another potential reason for the Skullcandy Push Active earbuds not charging problem could be a faulty battery.

If the earbuds’ battery has a manufacturing flaw, it might struggle to hold a charge or may not charge at all.

4. Software Glitches

Sometimes, the software in your earbuds might encounter a hiccup or encounter issues with the firmware.

Restarting or resetting the earbuds can often resolve these problems.

5. Faulty Charging Port

If your earbuds aren’t charging, a potential cause could be a damaged charging port.

Over time, the charging port may suffer damage from regular use or accidental drops, leading to difficulties in charging your earbuds.

6. Incorrect Placement in the Charging Case

It’s crucial to place your earbuds in the charging case accurately.

If they’re not aligned correctly, the charging contacts won’t connect, resulting in your earbuds not charging.

7. Insufficient Charge in the Case

When the charging case has a low battery level, it won’t effectively charge your earbuds.

Ensure that the case is adequately charged before attempting to charge your earbuds.

8. Charger Issues

If you use a charger or charging cable that’s not compatible, it might lead to problems with charging your Skullcandy Push Active earbuds.

9. Neglected Reset

Forgetting to reset them can be a factor. These earbuds need a manual reset every 3 months, but it’s an easy fix by placing them back in their case.

10. Internal Circuit Problem

There could be an issue with the internal circuit of either the charging case or the earbuds, possibly damaged or malfunctioning.

Skullcandy Push Active Not Charging (15 Fixes)

Now you know why it happens. Let’s know the solutions to solve the Skullcandy push active charging problem.

1. Put the Earbuds in the Case Properly

At times, if the earbuds are not positioned well in the charging case, the red light may not appear, indicating an improper placement.

So, make sure to properly position your earbuds on the charging posts. Gently press or adjust them to fit securely.

When in mono mode, the left earpiece is utilized more, depleting its battery faster.

Hence, after placing the earbuds in the case, give them a few moments to initiate the charging process.

Additionally, confirm that the case lid is securely closed. A clicking sound will confirm that the lid is properly shut.

2. Use a Compatible Charger and Power Cable

Your earbuds come with a charging cable, but there’s no charging brick included.

To charge them, you’ll need to use a charger from another brand. Make sure to use a high-quality charger with a rating below 18W (5V/3.6A).

Additionally, stick to the charging cable provided with your Skullcandy earbuds.

Using incompatible or inexpensive chargers may result in slow or inefficient charging.

If needed, you can also charge your earbuds using your laptop or a power bank, using the correct cable.

3. Replace the Batteries in Your Earbuds

As time passes, the batteries in your earbuds might wear down and not be able to hold a charge as well.

If the solutions mentioned earlier don’t help, think about getting new batteries.

Get in touch with Skullcandy customer support to ask about options and steps for changing the batteries.

They will help you through the steps and give the support you need.

4. Check for Firmware Updates

Sometimes, Skullcandy provides updates for the firmware to fix bugs and improve how your earbuds work.

Simply connect your earbuds to a device with the Skullcandy app, and see if there are any updates for the firmware.

By installing the most recent firmware, you might resolve the problem with charging.

5. Restart and Reset the Earbuds

If you’re experiencing minor software issues with your Skullcandy Push Active earbuds, a simple restart can often do the trick.

Just turn off your earbuds and then turn them back on.

If the issue continues, consider resetting the earbuds to their original settings. Check the user manual for guidance on how to perform a reset.

6. Turn Off Power-Saving Mode

If you’ve turned on the power-saving mode on your device, it might reduce the charging speed, leading to slow or no charging.

Turn off the power-saving mode and see if the earbuds begin charging properly.

7. Check the Case for any Damage

As mentioned earlier, the charging pins in the case play a crucial role in charging your earbuds.

If these pins are damaged, it’s necessary to have them repaired to resolve the issue.

The design of the charging pins may vary based on your earbud model, but generally, they protrude outward.

If you observe a pin that is pushed in, as illustrated in the image above, it could be the reason behind the problem.

If your warranty is still valid, you might have the option to receive a replacement case, depending on the nature of the damage.

Simply go to Skullcandy’s Warranty Page and complete the Warranty Claim Form.

8. Clear the Charging Ports

As time passes, dust, lint, and particles can gather in the charging ports of your earbuds, causing a blockage in the charging process.

Take a gentle approach by using a soft, dry cloth or a small brush to clean the ports.

Make sure there’s no leftover residue that could disrupt the connection between the charging cable and the earbuds.

9. Keep the charging case pins clean

Just like the earbuds, it’s important to keep the charging pins of your Skullcandy earbuds clean.

If there’s dirt on these pins, it can block the flow of power, causing your Skullcandy Push Active to not charge.

Therefore, it’s crucial to clean the charging case pins. To do this, grab a cotton cloth, a toothpick, and some rubbing alcohol.

Apply a few drops of rubbing alcohol to the cloth and gently wipe it onto the pins.

Use the toothpick to carefully remove any dirt from the pins and then wipe them clean with the cloth.

Once you’ve cleaned both the charging poles of your Skullcandy Push Active and their charging case pins, place the earbuds back into the case.

With any luck, they should begin charging again.

10. Check for Any Fault in the Charging Case

If your Skullcandy Push Active isn’t charging, it might be due to a problem with the charging case.

Usually, when the charging case is faulty, it means that its battery has encountered some issues.

A damaged battery in the charging case leads to an inability to hold a charge, resulting in your earbuds not getting charged.

Typically, the battery in the charging case may malfunction due to moisture or physical damage.

To address this, you can place the case under sunlight for a few minutes.

However, if you’ve accidentally dropped the case, there’s a possibility that the power cable is no longer connected to the battery, disrupting the flow of current to the case pins.

In such situations, it’s advisable to seek the assistance of a gadget technician.

They can quickly resolve the issue, as fixing it at home might be challenging for you.

11. Turn Both Earbuds off Before Placing Them in the Case

Make sure to switch off both earbuds before putting them in the case.

Sometimes, just turning them off before placing them in the case can fix the problem.

To put it simply, ensure that neither earbud is in the charging case unless both are switched off.

12. Drain the Battery Completely

If you’ve been using the earbuds in mono mode for an extended period, one battery might run out faster than the other.

This imbalance in battery levels can cause issues when trying to charge them in the case.

An obvious indicator of this problem is that one of your Skullcandy earbuds will charge, while the other one won’t.

To resolve this, you’ll need to completely use up both batteries to equalize their charge status and then recharge them to full capacity.

13. Keep Earbud Temperature Stable

In very cold or hot conditions, your Skullcandy Push Active may cease charging.

This is because the lithium-ion batteries within them become inactive in extreme temperatures.

If you’ve been utilizing your earbuds in a sauna, steam room, or chilly environment, it might have led to the charging issue.

To resolve this, allow your Skullcandy Push Active to return to a regular, or we can say room, temperature.

Leave your earbuds in a room for 2 to 3 hours. Afterward, attempt to charge your earbuds again.

14. Consider Professional Assistance

If your Skullcandy Push Active earbuds are still not charging despite your efforts, it’s advisable to seek help from professionals.

Contact authorized Skullcandy service centers or certified technicians who specialize in repairing audio devices.

These experts possess the expertise and specific tools needed to identify the underlying issues causing the charging problem and address them effectively.

They will make every effort to revive your earbuds, so don’t hesitate to seek their assistance!

15. Contact Skullcandy Support

If you’ve attempted all the suggested methods and the problem still lingers, consider initiating a Skullcandy warranty claim.

Since Skullcandy earbuds are covered by a 1-year warranty, you can get a replacement if there’s a manufacturing problem.

CONTACT Skullcandy:

[email protected]
01142700400
Monday – Friday
10:00am to 4:00pm

Tips for Taking Good Care of Skullcandy Push Active Earbuds

Making sure your Skullcandy Push Active Earbuds stay in great condition is important for enjoying your music.

Here are some simple tips to take care of your earbuds:

1. Keep Them Clean:

Use a soft cloth to gently wipe away any dirt or earwax. Don’t use anything sharp that might damage them.

2. Store Properly:

When you’re not using the earbuds, put them in their case. This helps keep them clean and prevents the cords from getting tangled.

3. Handle with Care:

Be careful when you hold and use your earbuds. Try not to drop them or put too much pressure on them to keep them working well.

4. Charge the Right Way:

Follow the charging instructions from Skullcandy. Once they’re fully charged, unplug them to help the battery last longer.

5. Avoid Too Much Water:

While the earbuds can handle some water, it’s best to keep them away from heavy rain or water submersion.

6. Update Software:

Check for updates for your earbuds regularly. This can make sure they work their best and might add new features.

7. Watch the Temperature:

Don’t leave your earbuds in really hot or cold places. Extreme temperatures can affect how well they work.

8. Use the Right Stuff:

Stick to using accessories that Skullcandy recommends, like charging cables and ear tips. Using other accessories might cause problems.

Follow these easy tips, and your Skullcandy Push Active Earbuds should stay in good condition, giving you great music whenever you want.

Conclusion

In conclusion, if your Skullcandy push active not charging, there are a few simple things you can do to fix it.

First, check to make sure everything is properly connected. Also, make sure you are using the correct power source.

Sometimes, updating the earbuds’ software can also be a simple solution to this problem.

It is important to take care of your earbuds. Keep them updated, and handle the charging accessories carefully.

In short, the solution to the “Skullcandy Push Active Not Charging” problem is to do a simple check and take good care of your earbuds.

Follow these tips, and I hope you can enjoy music on your earbuds again.

If you like this post, please share it. Follow our website to get the latest post updates.

Also Read:

[2024] Skullcandy Push Active Not Charging – (15 Easy Fixes)